Main Characteristics 1.Pipeline shape capacitor(new patent product),the area of radiate
heat is more than traditional capacitor.
2.In the equal condition,the temperature of Pipeline shape
capacitor are less than traditional capacitor.
3.Use the polypropylene metallized film for material,with small
size,light weight,and easy installation and maintenance(the
unloadable seat).
4.Adopts fantastic golden and silver metal printing(patent).
5.With high reliability,the market quality satisfaction rate is
99.99%,with one years guarantee .
6.High safety,with discharge resistance and over-pressure
protective device inside.
7.Low dielectric loss and perfect self-healing performance.
8.Adopts nontoxic,environment friendly impregnated material made of
solid capacitor wax. | Specification | Rated Voltage(V) | Rated Reactive Power(KVAR) | Total Capacitance(uF) | Dimensions(mm) | Drawing No | Outgoing terminal | | 0.25-24-3YN | 250 | 24 | 3×407.6 | 240×125×270 | | M8 | | 0.25-20-3YN | 230 | 20 | 3×339.7 | 240×125×270 | | 0.25-15-3YN | 230 | 15 | 3×254.8 | 178×70×280 | C | M6 | | 0.25-10-3YN | 230 | 10 | 3×170 | 178×70×260 | | 0.25-7.5-3YN | 230 | 7.5 | 3×127.3 | 178×70×220 | | 0.25-5-3YN | 230 | 5 | 3×84.9 | 178×70×165 | | 0.25-3-3YN | 230 | 3 | 3×51 | 178×70×165 |
Main Technical Characteristics :
1.Apply standard:GB/T12747.1-2004 IEC60831-1:1996
2.Apply
condition:Indoor,-25°C~40°C,humidity:<=80%RH,height<=2000MSL
3.Rated voltage:230VAC.250VAC.400VAC.415VAC.450VAC.525VAC.690VAC
4.Rated output:1~60Kvar
5.Capacitance tolence:0~10%
6.Voltage endurance:2Un 10 seconds between T-T,3000VAC 10 seconds
between T-C.
7.Loss angle tangent:Less than 0.1%(rated voltage at 20°C).
8.Ceiling voltage:1.1Un(root mean square value )
9.Ceiling current:1.3In(root mean square value )
10.Self-discharge feature:The terminal voltage will reduce below
50V in 3 minutes after disconnecting from power line. Experiment Regulate:
1.Environment temperature:60°C constant temperature
2.Voltage:650V
3.Continuance Time:48hours
4.Difference in temperature less than 6°C Install Notes:
1.Install it in the dry and well-ventilated place,prevent it from
the corrosive gas or dust,from the direct sunlight and the rainy or
snow.
2.The installation gap of two capacitors should be more than 50mm
to benefit for heat radiation.
3.The connect wire should wear the capacitor over 1.3In and is
reliable connection.
4.To regulation the power factor,connect anti-rush reactor or
capacity contactor to avoid of rush current damaging the capacitor.
5.Using serial inductors when capacitors used in the environment
that with high harmonic wave content.
6.To avoid of the superposing voltage damaging the
capacitor,capacitor must be discharged over 3 minutes before
re-input.
7.The capacitor should be used under rated voltage and current,or
its life will be reduced if under an overrated condition. Contour drawing and size:
|
